How far from either side of a school bus does the danger zone extend?

The danger zones may extend as much as 30 feet from the front bumper with the first 10 feet being the most dangerous, 10 feet from the left and right sides of the bus and 10 feet behind the rear bumper of the school bus.

How far is the blind spot behind the bus?

A school bus has blind spots immediately below the side flat mirrors, immediately in front of the side flat mirrors, and directly behind the rear bumper. Rear blind spots typically extend 50 to 150 feet behind a bus but can sometimes extend up to 400 feet, depending on the length of the vehicle.

IT IS INTERESTING:  Best answer: How much does it cost to replace a motorhome windshield?

Where should students walk to after exiting the bus?

Where should students walk to after exiting the bus? Tell students to exit the bus and walk at least 10 feet away from the side of the bus to a position where the driver can plainly see all students.

When adjusting the mirrors how far should you see to the side of the bus?

The outside flat mirrors should be adjusted so that you can see: 200 feet or 4 bus lengths behind the bus. The side of the bus.

How far from the nearest rail should a school bus stop at a highway rail crossing?

Any person driving a school bus and approaching a railroad-highway grade crossing shall stop within 50 feet but not less than 15 feet from the nearest rail of such railroad and shall not proceed until he or she can do so safely when a highway sign is indicating that a train is approaching or when the driver can hear or …

What are the mirrors on a school bus called?

Convex mirrors are typically mounted on the left and ride sides of the bus. They are usually located just below the flat mirror. A certain amount of distortion occurs when looking into the convex mirrors. However, the benefit of the convex mirror is that it allows the driver to see a wider field of view.

Which type of mirrors allow you to see the left and right sides of the bus at a wide angle?

The convex mirrors are located below the outside flat mirrors. They are used to monitor the left and right sides at a wide angle. They provide a view of traffic, clearances, and students at the side of the bus.

IT IS INTERESTING:  Can you turn a school bus into an RV?

Which is a safe practice for loading and unloading students at a turn around stop?

The recommended procedures are: Activate warning flasher system at least 100 feet prior to making a stop. Approach the loading zone slowly and carefully. Direct students to wait in an orderly fashion safely back from the roadway.

How far does the danger zone extend around the bus?

The danger zones may extend as much as 30 feet from the front bumper with the first 10 feet being the most dangerous, 10 feet from the left and right sides of the bus and 10 feet behind the rear bumper of the school bus.

What position should students be in front of the bus before they cross the roadway?

students. What position should students be in front of the bus before they cross the roadway? At least 10 feet in front of the right corner of the bumper, but still remaining away from the front of the school bus.

Which mirror is used in buses?

Convex mirrors are typically mounted on the left and ride sides of the bus. They are usually located just below the flat mirror. A certain amount of distortion occurs when looking into the convex mirrors. However, the benefit of the convex mirror is that it allows the driver to see a wider field of view.

What is the primary purpose of the crossover mirror system on school buses?

Crossover mirrors are used to help a school bus driver see the danger zone area directly in front of the bus, as well as the danger zone areas to the left and right sides of the bus, including the area from the front of the bus to the service door.

IT IS INTERESTING:  How do truck camper toilets work?

When stopped at a railroad crossing while operating a school bus you should?

Stop the bus within not less than 15 feet or more than 50 feet from the rails nearest the front of the bus. On multiple-lane roads, stop only in the right lane unless it is necessary to make a left turn immediately after crossing the railroad tracks.

When crossing train tracks What should you not do?

Never drive around the gates. If the gate is down, or raising or lowering, do not cross the tracks. If your vehicle has a standard (manual) transmission, do not change gears while crossing the tracks. If you cannot complete the shift, your vehicle could be stalled on the tracks.

What must a driver do when approaching a railroad crossing where the barriers are down?

What must a driver do when approaching a railroad crossing where the barriers are open? Approach at a moderate speed and observe the tracks to the right and left.

Campers